PDA

View Full Version : GLOCK PDW



Gabriel Suarez
05-09-2016, 10:09 AM
https://youtu.be/250QUf-C5FA

DogDoc
05-09-2016, 10:55 AM
Gabe are you running a folder on his now? If so, which one?

Doc

Gabriel Suarez
05-09-2016, 11:32 AM
No I am not. Added too much length.

baker
05-09-2016, 01:24 PM
How did the ATF deal with their engraving requirement on this? When I did an SBR I had to engrave the receiver.

5x5
05-09-2016, 02:41 PM
Not an Sbr.

Gabriel Suarez
05-09-2016, 02:50 PM
How did the ATF deal with their engraving requirement on this? When I did an SBR I had to engrave the receiver.


Yes...that is what would be necessary.

GemJedi
06-02-2016, 07:33 PM
What is the total length with a Glock 17, factory barrel?

Yondering
06-02-2016, 07:51 PM
What is the total length with a Glock 17, factory barrel?

Should be right about 19.5"-19.75" on a G17. It's 19" on a G19.

GemJedi
06-02-2016, 08:03 PM
I researched and found four candidates for bags. Anyone with the PDW on a Glock 17 are invited to weigh in. I am looking for something minimalist. for the car.

http://www.opticsplanet.com/elite-survival-systems-pistol-case.html?_iv_code=7J-GC-AABBCF-P20S-B

http://www.elitesurvival.com/rifle-cases/assault-systems-submachine-gun-cases/

http://www.elitesurvival.com/rifle-cases/covert-operations-discreet-carry-cases/

http://www.midwayusa.com/product/110478/boyt-thompson-center-contender-case-21-x-10-canvas-black

bassbones
06-20-2016, 02:46 AM
For just the ENDO itself folded with three happy sticks (to add to my carry G17 when needed), I have a maxpedition neat freak that is working nicely

JB

mark greenman
08-04-2016, 06:42 AM
Gabe, which folder did you install for that demo video? Having the folding option would make or break it for me in terms of bag carry.

coastalcop
08-04-2016, 06:44 AM
Gabe,
did you get the happy stamp yet to be able to video demo for the crowds yet?

Wildcat
08-04-2016, 07:26 AM
so if this becomes an sbr, its legally a rifle then. right? which means you dont need a chl to carry it?


Sent from my iPhone using Tapatalk

steve_k
08-04-2016, 07:51 AM
so if this becomes an sbr, its legally a rifle then. right? which means you dont need a chl to carry it?


Sent from my iPhone using Tapatalk

I would highly suggest checking your local and state laws. With it being a riffle that probably puts it in another category as far as carry and transportation.

coastalcop
08-04-2016, 09:47 AM
Yes it would be on its face legal as a rifle SANS LTC (License to carry) in Texas. HOWEVER understand that probably 2 in a 100 cops know enough both about tax stamp weapons and current firearms laws to put it all together and say "yep, youre good to go" So if the question came up, anticipate some time on the side of the road, a call to a supervisor, and STILL perhaps a ride downtown till the "gun guy" can chime in. Easier all around to just get the LTC (or a reciprocal one) at the outset.


For instance I can carry nationwide under LEOSA as a cop, BUT I still have a LTC to facilitate firearms purchases (NICS check as a cop, jot down the LTC number with the permit) and in reciprocal states where the copper that puts me on the curb might not understand LEOSA (give them easy reasons to say yes)

Mustang10mm
08-04-2016, 04:31 PM
Hi Folks,

New member - straightforward question I hope has not been asked before... I'm interested in this for a Glock 20 Gen 4 10mm. Any chance it'll work, or that one that will is on it's way?

Thanks!

DogDoc
08-04-2016, 04:36 PM
Hi Folks,

New member - straightforward question I hope has not been asked before... I'm interested in this for a Glock 20 Gen 4 10mm. Any chance it'll work, or that one that will is on it's way?

Thanks!

The Endo stock is made for the Gen 3. I modified one for a Gen 4 by removing material with a dremel tool. It works fine.

Doc

Yondering
08-04-2016, 04:52 PM
Dogdoc, is that on a gen4 10mm, or on a small frame (9/40/357)?

Mustang10mm
08-05-2016, 09:14 PM
The Endo stock is made for the Gen 3. I modified one for a Gen 4 by removing material with a dremel tool. It works fine.

Doc

Thanks, Doc. I may try that.

M10mm